Sewing on a button and a snap with the Husqvarna Viking Designer Ruby 90 by Elaine Theriault November 26, 2021 written by Elaine Theriault November 26, 2021 274 Wow! The week has flown by, and it’s already Friday! I’ve had so much fun; playing with the different Inspira stabilizers, trying out different fabric types for machine embroidery, and mending that sweater yesterday was brilliant. All of it was super easy using the Husqvarna Viking Designer Ruby 90. Husqvarna Viking Designer Ruby 90 I’ll admit that I’m a bit of a lazy sewist. I love handwork, but if I can do the task with a sewing machine, I’ll do it. I have a jacket to repair today, and I was going to do it by hand, but that meant finding some hand needles, and well, the Designer Ruby 90 was calling to me. So, I’m repairing the jacket with the sewing machine. Now the repair is straightforward. A snap used to close the jacket, which I had initially stitched in place by hand, was coming loose, and I figured it was better to fix the snap now before it completely fell off and got lost. You know what they say – a stitch in time saves nine! It’s so easy to sew buttons on with the sewing machine, but did you know there are several ways to do that? Let’s have a look. I’ll start with the optional Button Foot with Placement Tool. It easily snaps onto the presser foot ankle. The Button Foot with Placement Tool What’s nice about the Button Foot is that if I need the button sewn on without a shank, it stays in the position shown above. If my fabric is thick, then I need the button sewn on with a shank. It’s easy to transition between the two settings as there’s a small gray lever on the right-hand side, and by pulling that forward, a plastic ridge appears at the front, and the shank (made of thread) forms over that ridge. The Button Foot set to sew a button with a thread shank Along the front of the Button Foot, you’ll notice that there’s a slot on either side of the foot. These slots hold the button in place. It can be tricky to get the button into the slots and get the holes lined up with the needle. However, there’s a handy tool that makes this job super simple. The Placement Tool has two prongs that you insert into the holes of the button. Use the prongs of the Placement Tool to grab the button. Then it’s simple to insert the button into the front slots. The way the Placement Tools grabs the button ensures the button’s holes are in line with the needle. Using the Placement Tool to insert the button into the Button Foot Then you can remove the tool, and you are ready to sew. But wait – the needle isn’t in the correct position in this photo because I did not select the stitch that I’ll use to sew on the button. The button sits in the Button Foot, ready to be stitched in place. It’s so easy; it’s child play! When I turn the Designer Ruby 90 on, the JoyOS Advisor appears on the opening screen. And let’s look in the bottom right-hand corner. What does that say? Sew on button! Wow – how easy is that? The JoyOS Advisor Selecting that icon opens a window with the correct stitch for sewing on the button. A tutorial to explain what supplies are needed and how to sew the stitch also appears. And even better, the Designer Ruby 90 is now ready to sew the button on. All the settings are taken care of by the JoyOS Advisor. I love it! The machine settings and a tutorial for sewing on a button appear on the screen. Now you’ll notice in the tutorial, that the Multipurpose tool is used to hold the button in place. If you need a thin or thick shank, the Multipurpose tool can be used instead of the Button Foot. The Multipurpose foot is part of the accessories for the Designer Ruby 90. Either option will work. The Multipurpose tool The default width of the stitch for sewing on the button is 3mm. That is pretty much an industry standard, but I still manually test the left and right needle position by manually turning the handwheel. The last thing I want is bits of broken buttons or needles flying around the studio. Manually checking the needle position for sewing the button on The other thing to note on the tack stitch used to sew on the button is the number of times the needle goes left to right. You’ll see in the settings that the default is 8. That’s probably a couple more than I would do if I were sewing the button by hand. You can increase or decrease that number. The default width and length of the standard stitch used to sew buttons Now that everything is ready, let’s see it in action. Isn’t that just the best? But I want to re-attach a snap, so I’ll use a slightly different technique to fix the jacket. I’ve removed the Button Foot, and I’m not going to use the Multipurpose Tool. I’m simply going to use the presser foot ankle to hold the snap in place. Only two sides of the snap were loose, so I didn’t need to secure it to the jacket. But if I had to, I could use some tape, which they recommended in the built-in tutorial. I carefully positioned the snap so the hole would line up with the needle. I manually tested that the needle would go back and forth and not hit the snap. Use the presser foot ankle to hold the snap in place while it’s tacked in place. That was too easy. Make sure you clean up the old threads first. And here is the snap, firmly attached on all sides. I really should’ve removed the rest of the hand stitching and secured all four sides of the snap with the Designer Ruby 90. Since each securing stitch took seconds, I might go back and do that. The snap is now securely back in place. WOW – WOW – WOW – that was so easy! I’m having so much fun creating new things and repairing things with the Husqvarna Viking Designer Ruby 90. It’s an excellent machine that does all kinds of jobs! My week is up, but you can bet that I’m scouring that pile of projects to see what else I can fix or create with this fabulous sewing and embroidery machine. Be sure to stop by your local Husqvarna Viking sewing machine dealer and ask for an in-person demo. You’ll be impressed. Thanks for stopping by this week, and until next time, Have a super day! Ciao! This is part 5 of 5 in this series Go back to part 4: How to fix a hole in a knit sweater with machine embroidery Print this page or save as a PDF 0qs391Cut-A-Way stabilizerDesigner Ruby 90film topper stabilizerhusqvarna vikingmachine embroiderymachine embroidery tutorialsmysewnetquiltingsewing machine reviewsstabilizer guidetutorialswater-soluble stabilizer FacebookTwitterPinterestLinkedinRedditWhatsappTelegramEmail Elaine Theriault Elaine Theriault is a teacher, writer and pattern designer who is completely obsessed with quilting. Elaine’s Tech Tips column (originally published in A Needle Pulling Thread magazine) is now available online in e-book format at QUILTsocial.com. When not quilting, she enjoys spending time with her two dogs, Lexi and Murphy, or can be found cycling across the country. Her blog is crazyquilteronabike.blogspot.com. previous post How to fix a hole in a knit sweater with machine embroidery next post QUILTsocial Live! with Elaine | Stabilizers for machine embroidery YOU MAY ALSO LIKE... 4 presser feet made to PIECE, QUILT, and... 4 more texture blocks for a fidget quilt... Embroidery is spectacular with the Husqvarna Viking Texture... 6 fun blocks for a fidget quilt with... Wi-Fi on the Husqvarna Viking Designer Ruby 90:... How to fix a hole in a knit... In machine embroidery: knit fabric stays put with... Inspira water-soluble stabilizers for superb machine embroidery results How to choose the right stabilizer for your... Leave a Comment Cancel Reply Save my name, email, and website in this browser for the next time I comment. Δ This site uses Akismet to reduce spam. Learn how your comment data is processed.